TOP
SSV Software Systems Register  Register
Log in to check your private messages  Log in to check your private messages
Startseite FAQ Search Mitglieder Profile  Log in 
SSV Support-Forum
RESOUT und CLKOUT am DNP/9200

 
Post new topic   Reply to topic    SSV-Forum Forum Index >>> DNP/9200
<<< Previous topic - Next topic >>>  
Display posts from previous:   
Author Message
dl7bj



Joined: 10 Jul 2006
Posts: 18
Location: Rotenburg, JO43PC

PostPosted: 22.02.2007, 23:05    Post subject: RESOUT und CLKOUT am DNP/9200 Reply with quote

Moin,

ich suche in den ganzen Unterlagen verzweifelt eine Beschreibung für
den PIN 35 und 37 vom DNP/9200, wahrscheinlich ist der Bildschirm
wieder verschmutzt Wink

Pin 35 RESOUT

Ist das ein Active-Low Signal, das dem Pegel an RESIN folgt, oder ist es noch
anderweitig verdrahtet?

Pin 37 CLKOUT

Was liegt hier für ein Clock-Signal an?

MfG
Thomas
Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger
ssc



Joined: 05 May 2006
Posts: 36

PostPosted: 23.02.2007, 16:07    Post subject: Reply with quote

Hallo dl7bj,

hier die Auflösung:
Quote:
Pin 35 RESOUT

Ist das ein Active-Low Signal, das dem Pegel an RESIN folgt, oder ist es noch
anderweitig verdrahtet?


Über Pin 29 RESIN wird der Eingang eines Supervisor-Baustein angesteuert, der daraufhin das Signal RESOUT (Pin 35) erzeugt. RESOUT ist dann für ca. 200ms auf einem Low-Pegel und dient gleichzeitig als System-Reset.
Bei einem Power-on-Reset bleibt RESOUT ca. 1.6sec auf low.

Quote:
Pin 37 CLKOUT

Was liegt hier für ein Clock-Signal an?


Der Pin CLKOUT des DNP/9200 ist an den programmierbaren Taktausgang PCK0 (Pin G6) der MCU angeschlossen (siehe Datenblatt AT91RM9200).

Schöne Grüße,

ssc
Back to top
View user's profile Send private message
dl7bj



Joined: 10 Jul 2006
Posts: 18
Location: Rotenburg, JO43PC

PostPosted: 23.02.2007, 22:32    Post subject: Reply with quote

Hallo,

Danke für die schnelle Antwort!

ssc wrote:


Über Pin 29 RESIN wird der Eingang eines Supervisor-Baustein angesteuert, der


Muss für den Supervisor der RESIN besser mit einem PullUp versehen werden, oder
ist der schon auf dem DNP/9200 vorhanden?

Gruss,
Thomas
Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger
ssc



Joined: 05 May 2006
Posts: 36

PostPosted: 26.02.2007, 10:52    Post subject: Reply with quote

Hallo dl7bj,

es ist bereits ein Pull-Up Widerstand auf dem DNP/9200.

Schöne Grüße,

ssc
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    SSV-Forum Forum Index >>> DNP/9200 All times are GMT + 1 Hour
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

SSV Software Systems GmbH

Dünenweg 5
30419 Hannover

Fon: +49(0)511  ·  40 000-0
Fax: +49(0)511  ·  40 000-40

sales@ssv-embedded.de


Impressum    ·    Datenschutz    ·    AGB

© 2023 SSV SOFTWARE SYSTEMS GmbH. Alle Rechte vorbehalten.

ISO 9001:2015